View GS88118T-115_1177097.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary GS88118/36T-11/11.5/100/80/66 100-Pin TQFP Commercial Temp Industrial Temp
1.11 9/2000Features
* FT pin for user-configurable flow through or pipelined operation * Single Cycle Deselect (SCD) Operation * IEEE 1149.1 JTAG-compatible Boundary Scan * On-chip write parity checking; even or odd selectable * 3.3 V +10%/-5% core power supply * 2.5 V or 3.3 V I/O supply * LBO pin for Linear or Interleaved Burst mode * Internal input resistors on mode pins allow floating mode pins * Default to Interleaved Pipeline mode * Byte Write (BW) and/or Global Write (GW) operation * Common data inputs and data outputs * Clock Control, registered, address, data, and control * Internal self-timed write cycle * Automatic power-down for portable applications * 100-lead TQFP package -11 -11.5 -100 -80 -66 10 ns 10 ns 12.5 ns 15 ns Pipeline tCycle 10 ns 4.0 ns 4.0 ns 4.0 ns 4.5 ns 5.0 ns 3-1-1-1 tKQ 225 mA 225 mA 225 mA 200 mA 185 mA IDD 11 ns 11.5 ns 12 ns 14 ns 18 ns Flow tKQ 15 ns 15 ns 15 ns 20 ns Through tCycle 15 ns 2-1-1-1 IDD 180 mA 180 mA 180 mA 175 mA 165 mA
512K x 18, 256K x 36 ByteSafeTM 100 MHz-66 MHz 3.3 V VDD 8Mb Sync Burst SRAMs 3.3 V and 2.5 V I/O
counter may be configured to count in either linear or interleave order with the Linear Burst Order (LBO) input. The Burst function need not be used. New addresses can be loaded on every cycle with no degradation of chip performance.
Flow Through/Pipeline Reads
The function of the Data Output register can be controlled by the user via the FT mode pin (Pin 14). Holding the FT mode pin low places the RAM in Flow Through mode, causing output data to bypass the Data Output Register. Holding FT high places the RAM in Pipeline mode, activating the risingedge-triggered Data Output Register.
SCD Pipelined Reads
The GS88118//36T is a SCD (Single Cycle Deselect) pipelined synchronous SRAM. DCD (Dual Cycle Deselect) versions are also available. SCD SRAMs pipeline deselect commands one stage less than read commands. SCD RAMs begin turning off their outputs immediately after the deselect command has been captured in the input registers.
Byte Write and Global Write
Byte write operation is performed by using Byte Write enable (BW) input combined with one or more individual byte write signals (Bx). In addition, Global Write (GW) is available for writing all bytes at one time, regardless of the byte write control inputs.
ByteSafeTM Parity Functions
The GS88118/36T features ByteSafe data security functions. See detailed discussion following.
Functional Description
Applications
The GS88118//36T is a 9,437,184-bit high performance synchronous SRAM with a 2-bit burst address counter. Although of a type originally developed for Level 2 Cache applications supporting high performance CPUs, the device now finds application in synchronous SRAM applications, ranging from DSP main store to networking chip set support.
Sleep Mode
Low power (Sleep mode) is attained through the assertion (high) of the ZZ signal, or by stopping the clock (CK). Memory data is retained during Sleep mode.
Core and Interface Voltages
The GS88118//36T operates on a 3.3 V power supply, and all inputs/outputs are 3.3 V- and 2.5 V-compatible. Separate output power (VDDQ) pins are used to decouple output noise from the internal circuit.
Controls
Addresses, data I/Os, chip enables (E1, E2), address burst control inputs (ADSP, ADSC, ADV) and write control inputs (Bx, BW, GW) are synchronous and are controlled by a positive-edge-triggered clock input (CK). Output enable (G) and power down control (ZZ) are asynchronous inputs. Burst cycles can be initiated with either ADSP or ADSC inputs. In Burst mode, subsequent burst addresses are generated internally and are controlled by ADV. The burst address Rev: 1.11 9/2000 1/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
GS88118 100-Pin TQFP Pinout
NC NC NC VDDQ VSS NC NC DQB1 DQB2 VSS VDDQ DQB3 DQB4 FT VDD DP VSS DQB5 DQB6 VDDQ VSS DQB7 DQB8 DQB9 NC VSS VDDQ NC NC NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 512K X 18 10 71 Top View 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CK GW BW G ADSC ADSP ADV A8 A9
A6 A7 E1 E2 NC NC BB BA A17 VDD VSS
A18 NC NC VDDQ VSS NC DQA9 DQA8 DQA7 VSS VDDQ DQA6 DQA5 VSS QE VDD ZZ DQA4 DQA3 VDDQ VSS DQA2 DQA1 NC NC VSS VDDQ NC NC NC
A1 A0 TMS TDI VSS VDD TDO TCK A10 A11 A12 A13 A14 A15 2/33
LBO A5 A4
Rev: 1.11 9/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
A16 (c) 2000, Giga Semiconductor, Inc.
A3 A2
Preliminary GS88118/36T-11/11.5/100/80/66
GS88136 100-Pin TQFP Pinout
DQC9 DQC8 DQC7 VDDQ VSS DQC6 DQC5 DQC4 DQC3 VSS VDDQ DQC2 DQC1 FT VDD DP VSS DQD1 DQD2 VDDQ VSS DQD3 DQD4 DQD5 DQD6 VSS VDDQ DQD7 DQD8 DQD9
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 256K x 36 10 71 Top View 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CK GW BW G ADSC ADSP ADV A8 A9
A6 A7 E1 E2 BD BC BB BA A17 VDD VSS
DQB9 DQB8 DQB7 VDDQ VSS DQB6 DQB5 DQB4 DQB3 VSS VDDQ DQB2 DQB1 VSS QE VDD ZZ DQA1 DQA2 VDDQ VSS DQA3 DQA4 DQA5 DQA6 VSS VDDQ DQA7 DQA8 DQA9
A3 A2 A1 A0 TMS TDI VSS VDD TDO TCK A10 A11 A12 A13 A14 A15 3/33
LBO A5 A4
Rev: 1.11 9/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
A16 (c) 2000, Giga Semiconductor, Inc.
Preliminary GS88118/36T-11/11.5/100/80/66
TQFP Pin Description Pin Location
37, 36 35, 34, 33, 32, 100, 99, 82, 81, 44, 45, 46, 47, 48, 49, 50, 92 80 63, 62, 59, 58, 57, 56, 53, 52 68, 69, 72, 73, 74, 75, 78, 79 13, 12, 9, 8, 7, 6, 3, 2 18, 19, 22, 23, 24, 25, 28, 29 51, 80, 1, 30 58, 59, 62, 63, 68, 69, 72, 73, 74 8, 9, 12, 13, 18, 19, 22, 23, 24 51, 52, 53, 56, 57 75, 78, 79, 1, 2, 3, 6, 7 25, 28, 29, 30 16 66 87 93, 94 95, 96 95, 96 89 88 98 97 86 83 84, 85
Symbol
A0, A1 A2-A17 A18 DQA1-DQA8 DQB1-DQB8 DQC1-DQC8 DQD1-DQD8 DQA9, DQB9, DQC9, DQD9 DQA1-DQA9 DQB1-DQB9 NC DP QE BW BA, BB BC, BD NC CK GW E1 E2 G ADV ADSP, ADSC
Typ e
I I I I/O
Description
Address field LSBs and Address Counter preset Inputs Address Inputs Address Inputs Data Input and Output pins ( x36 Version)
I/O I/O
Data Input and Output pins Data Input and Output pins
-- I O I I I -- I I I I I I I
No Connect Parity Input; 1 = Even, 0 = Odd Parity Error Out; Open Drain Output Byte Write--Writes all enabled bytes; active low Byte Write Enable for DQA, DQB Data I/Os; active low Byte Write Enable for DQC, DQD Data I/Os; active low ( x36 Version) No Connect (x18 Version) Clock Input Signal; active high Global Write Enable--Writes all bytes; active low Chip Enable; active low Chip Enable; active high Output Enable; active low Burst address counter advance enable; active low Address Strobe (Processor, Cache Controller); active low
Rev: 1.11 9/2000
4/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Pin Location
64 14 31 38 39 42 43 15, 41, 65, 91 5,10,17, 21, 26, 40, 55, 60, 67, 71, 76, 90 4, 11, 20, 27, 54, 61, 70, 77
Symbol
ZZ FT LBO TMS TDI TDO TCK VDD VSS VDDQ
Typ e
I I I I I O I I I I
Description
Sleep mode control; active high Flow Through or Pipeline mode; active low Linear Burst Order mode; active low Scan Test Mode Select Scan Test Data In Scan Test Data Out Scan Test Clock Core power supply I/O and Core Ground Output driver power supply
Rev: 1.11 9/2000
5/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
GS881881E18/36 Block Diagram
Register
A0-An
D
Q A0 D0 A1 D1 Q1 Counter Load A Q0 A0 A1
LBO ADV CK ADSC ADSP GW BW BA
Register
Memory Array
Q D Q 36 D 36
Register
D BB
Q 4 4
Register
D BC
Q
Register
D
Q
Register
Register 4
D BD
Q
Register
36 36 36
D
Q
E1 E2
Register
D
Q
32 Parity Encode 4 Parity Compare 36 36
Register
D
Q
FT G Power Down Control
1
ZZ
DQx0-DQx9
QE
D DP
Note: Only x36 version shown for simplicity.
ByteSafeTM Parity Functions
Rev: 1.11 9/2000 6/33 (c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Q
Q D
Register
Preliminary GS88118/36T-11/11.5/100/80/66
This SRAM includes a write data parity check that checks the validity of data coming into the RAM on write cycles. In Flow Through mode, write data errors are reported in the cycle following the data input cycle. In Pipeline mode, write data errors are reported one clock cycle later. (See Write Parity Error Output Timing Diagram.) The Data Parity Mode (DP) pin must be tied high to set the RAM to check for even parity or low to check for odd parity. Read data parity is not checked by the RAM as data. Validity is best established at the data's destination. The Parity Error Output is an open drain output and drives low to indicate a parity error. Multiple Parity Error Output pins may share a common pull-up resistor.
Write Parity Error Output Timing Diagram
CK DQ
Flow Through Mode
D In A tKQ tLZ
D In B tHZ tKQX Err A
D In C
D In D
D In E
QE
Err C
Pipelined Mode
DQ
D In A
D In B tKQ tLZ
D In C tHZ tKQX Err A
D In D
D In E
QE
Err C
BPR 1999.05.18
Mode Pin Functions Mode Name
Burst Order Control Output Register Control Power Down Control ByteSafe Data Parity Control Rev: 1.11 9/2000
Pin Name
LBO FT ZZ DP 7/33
State
L H or NC L H or NC L or NC H L H or NC
Function
Linear Burst Interleaved Burst Flow Through Pipeline Active Standby, IDD = ISB Check for Odd Parity Check for Even Parity (c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Note: There are pull-up devices on the LBO, DP and FT pins and a pull down device on the ZZ pin, so those input pins can be unconnected and the chip will operate in the default states as specified in the above table.
Burst Counter Sequences
Linear Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0] 1st address 2nd address 3rd address 4th address 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 1st address 2nd address 3rd address 4th address
Interleaved Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0] 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00
BPR 1999.05.18
Note: The burst counter wraps to initial state on the 5th clock.
Note: The burst counter wraps to initial state on the 5th clock.
Byte Write Truth Table Function
Read Read Write byte a Write byte b Write byte c Write byte d Write all bytes Write all bytes
GW
H H H H H H H L
BW
H L L L L L L X
BA
X H L H H H L X
BB
X H H L H H L X
BC
X H H H L H L X
BD
X H H H H L L X
Notes
1 1 2, 3 2, 3 2, 3, 4 2, 3, 4 2, 3, 4
Notes: 1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs. 2. Byte Write Enable inputs BA, BB, BC, and/or BD may be used in any combination with BW to write single or multiple bytes. 3. All byte I/Os remain High-Z during all write operations regardless of the state of Byte Write Enable inputs. 4. Bytes "C" and "D" are only available on the x36 version.
Rev: 1.11 9/2000
8/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Synchronous Truth Table Operation
Deselect Cycle, Power Down Deselect Cycle, Power Down Deselect Cycle, Power Down Read Cycle, Begin Burst Read Cycle, Begin Burst Write Cycle, Begin Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst
Address Used
None None None External External External Next Next Next Next Current Current Current Current
State Diagram Key5
X X X R R W CR CR CW CW
E1
H L L L L L X H X H X H X H
E22
(x36only)
ADSP ADSC
X L H L H H H X H X H X H X L X L X L L H H H H H H H H
ADV
X X X X X X L L L L H H H H
W3
X X X X F T F F T T F F T T
DQ4
High-Z High-Z High-Z Q Q D Q Q D D Q Q D D
X F F T T T X X X X X X X X
Notes: 1. X = Don't Care, H = High, L = Low. 2. For x36 Version, E = T (True) if E2 = 1; E = F (False) if E2 = 0. 3. W = T (True) and F (False) is defined in the Byte Write Truth Table preceding. 4. G is an asynchronous input. G can be driven high at any time to disable active output drivers. G low can only enable active drivers (shown as "Q" in the Truth Table above). 5. 6. 7. All input combinations shown above are tested and supported. Input combinations shown in gray boxes need not be used to accomplish basic synchronous or synchronous burst operations and may be avoided for simplicity. Tying ADSP high and ADSC low allows simple non-burst synchronous operations. See BOLD items above. Tying ADSP high and ADV low while using ADSC to load new addresses allows simple burst operations. See ITALIC items above.
Rev: 1.11 9/2000
9/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Simplified State Diagram
X
Deselect W W Simple Synchronous Operation R R
X CW
First Write
R CR
First Read
X CR
Simple Burst Synchronous Operation
W R X Burst Write CR CW
R
Burst Read
X
CR
Notes: 1. The diagram shows only supported (tested) synchronous state transitions. The diagram presumes G is tied low. 2. The upper portion of the diagram assumes active use of only the Enable (E1and E2) and Write (BA, BB, BC, BD, BW, and GW) control inputs, and that ADSP is tied high and ADSC is tied low. 3. The upper and lower portions of the diagram together assume active use of only the Enable, Write, and ADSC control inputs, and assumes ADSP is tied high and ADV is tied low.
Rev: 1.11 9/2000
10/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Simplified State Diagram with G
X
Deselect W W X W CW R R
First Write
R CR
First Read
X CR
CW
W X Burst Write R CR W CW
R X
Burst Read
CW
CR
Notes: 1. The diagram shows supported (tested) synchronous state transitions plus supported transitions that depend upon the use of G. 2. Use of "Dummy Reads" (Read Cycles with G High) may be used to make the transition from Read cycles to Write cycles without passing through a Deselect cycle. Dummy Read cycles increment the address counter just like normal Read cycles. 3. Transitions shown in grey tone assume G has been pulsed high long enough to turn the RAM's drivers off and for incoming data to meet Data Input Set Up Time.
Rev: 1.11 9/2000
11/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
VDD VDDQ VCK VI/O VIN IIN IOUT PD TSTG TBIAS
Description
Voltage on VDD Pins Voltage in VDDQ Pins Voltage on Clock Input Pin Voltage on I/O Pins Voltage on Other Input Pins Input Current on Any Pin Output Current on Any I/O Pin Package Power Dissipation Storage Temperature Temperature Under Bias
Value
-0.5 to 4.6 -0.5 to VDD -0.5 to 6 -0.5 to VDDQ +0.5 ( 4.6 V max.) -0.5 to VDD +0.5 ( 4.6 V max.) +/-20 +/-20 1.5 -55 to 125 -55 to 125
Unit
V V V V V mA mA W
oC oC
Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component.
Recommended Operating Conditions Parameter
Supply Voltage I/O Supply Voltage Input High Voltage Input Low Voltage Ambient Temperature (Commercial Range Versions) Ambient Temperature (Industrial Range Versions)
Symbol
VDD VDDQ VIH VIL TA TA
Min.
3.135 2.375 1.7 -0.3 0 -40
Typ.
3.3 2.5 -- -- 25 25
Max.
3.6 VDD VDD +0.3 0.8 70 85
Unit
V V V V C C
Notes
1 2 2 3 3
Notes: 1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case at both 2.75 V VDDQ 2.375 V (i.e., 2.5 V I/O) and 3.6 V VDDQ 3.135 V (i.e., 3.3 V I/O), and quoted at whichever condition is worst case. 2. This device features input buffers compatible with both 3.3 V and 2.5 V I/O drivers. 3. Most speed grades and configurations of this device are offered in both Commercial and Industrial Temperature ranges. The part number of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 4. Input Under/overshoot voltage must be -2 V > Vi < VDD +2 V with a pulse width not to exceed 20% tKC.
Rev: 1.11 9/2000
12/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Undershoot Measurement and Timing
VIH VDD + 2.0 V VSS 50% VSS - 2.0 V 20% tKC VIL 50% VDD
Overshoot Measurement and Timing
20% tKC
Capacitance
(TA = 25oC, f = 1 MHZ, VDD = 3.3 V)
Parameter
Input Capacitance Input/Output Capacitance Note: These parameters are sample tested.
Symbol
CIN CI/O
Test conditions
VIN = 0 V VOUT = 0 V
Typ.
4 6
Max.
5 7
Unit
pF pF
Package Thermal Characteristics Rating
Junction to Ambient (at 200 lfm) Junction to Ambient (at 200 lfm) Junction to Case (TOP)
Layer Board
single four --
Symbol
RJA RJA RJC
Max
40 24 9
Unit
C/W C/W C/W
Notes
1,2 1,2 3
Notes: 1. Junction temperature is a function of SRAM power dissipation, package thermal resistance, mounting board temperature, ambient. Temperature air flow, board density, and PCB thermal resistance. 2. SCMI G-38-87 3. Average thermal resistance between die and top surface, MIL SPEC-883, Method 1012.1
Rev: 1.11 9/2000
13/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
AC Test Conditions Parameter
Input high level Input low level Input slew rate Input reference level Output reference level Output load
Conditions
2.3 V 0.2 V 1 V/ns 1.25 V 1.25 V Fig. 1& 2
Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output Load 2 for tLZ, tHZ, tOLZ and tOHZ 4. Device is deselected as defined by the Truth Table. Output Load 1 DQ 50 VT = 1.25 V
* Distributed Test Jig Capacitance
Output Load 2 2.5 V 30pF* DQ 5pF* 225 225
DC Electrical Characteristics Parameter
Input Leakage Current (except mode pins) ZZ Input Current Mode Pin Input Current Output Leakage Current Output High Voltage Output High Voltage Output Low Voltage
Symbol
IIL IINZZ IINM IOL VOH VOH VOL
Test Conditions
VIN = 0 to VDD VDD VIN VIH 0 V VIN VIH VDD VIN VIL 0 V VIN VIL Output Disable, VOUT = 0 to VDD IOH = -8 mA, VDDQ = 2.375 V IOH = -8 mA, VDDQ = 3.135 V IOL = 8 mA
Min
-1 uA -1 uA -1 uA -300 uA -1 uA -1 uA 1.7 V 2.4 V --
Max
1 uA 1 uA 300 uA 1 uA 1 uA 1 uA -- -- 0.4 V
Rev: 1.11 9/2000
14/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Operating Currents
-11 Parameter Test Conditions Symbol 0 to 70C 225 180 30 30 80 65 -40 to 85C 235 190 40 40 90 75 -11.5 0 to 70C 225 180 30 30 80 65 -40 to 85C 235 190 40 40 90 75 -100 0 to 70C 225 180 30 30 80 65 -40 to 85C 235 190 40 40 90 75 0 to 70C 200 175 30 30 70 55 -80 -40 to 85C 210 185 40 40 80 65 0 to 70C 185 165 30 30 60 50 -66 -40 to 85C 195 175 40 40 70 60 Unit
Operating Current
Device Selected; All other inputs VIH or VIL Output open
IDD Pipeline IDD Flow-Thru ISB Pipeline ISB Flow-Thru IDD Pipeline IDD Flow-Thru
mA mA mA mA mA mA
Standby Current
ZZ VDD - 0.2V
Deselect Current
Device Deselected; All other inputs VIH or VIL
Rev: 1.11 9/2000
15/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 AC Electrical Characteristics
Parameter Clock Cycle Time Pipeline Clock to Output Valid Clock to Output Invalid Clock to Output in Low-Z Clock Cycle Time FlowThru Clock to Output Valid Clock to Output Invalid Clock to Output in Low-Z Clock HIGH Time Clock LOW Time Clock to Output in High-Z G to Output Valid G to output in Low-Z G to output in High-Z Setup time Hold time ZZ setup time ZZ hold time ZZ recovery Symbol tKC tKQ tKQX tLZ
1
-11 Min 10 -- 1.5 1.5 15.0 -- 3.0 3.0 1.7 2 1.5 -- 0 -- 1.5 0.5 5 1 20 Max -- 4.0 -- -- -- 11.0 -- -- -- -- 4.0 4.0 -- 4.0 -- -- -- -- -- 10 --
-11.5 Min Max -- 4.0 -- -- -- 11.5 -- -- -- -- 4.2 4.2 -- 4.2 -- -- -- -- -- 10 -- 1.5 1.5
-100 Min Max -- 4.0 -- -- -- 12.0 -- -- -- -- 4.5 4.5 -- 4.5 -- -- -- -- -- Min 12.5 -- 1.5 1.5 15.0 -- 3.0 3.0 2 2.2 1.5 -- 0 -- 2.0 0.5 5 1 20
-80 Max -- 4.5 -- -- -- 14.0 -- -- -- -- 4.5 4.5 -- 4.5 -- -- -- -- -- Min 15 -- 1.5 1.5 20 -- 3.0 3.0 2.3 2.5 1.5 -- 0 -- 2.0 0.5 5 1 20
-66 Max -- 5 -- -- -- 18 -- -- -- -- 4.8 4.8 -- 4.8 -- -- -- -- --
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
1.5 1.5 15.0 -- 3.0 3.0 1.7 2 1.5 -- 0 -- 2.0 0.5 5 1 20
tKC tKQ tKQX tLZ1 tKH tKL tHZ1 tOE tOLZ1 tOHZ1 tS tH tZZS2 tZZH2 tZZR
15.0 -- 3.0 3.0 2 2.2 1.5 -- 0 -- 2.0 0.5 5 1 20
Notes: 1. These parameters are sampled and are not 100% tested. 2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold times as specified above.
Rev: 1.11 9/2000
16/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Write Cycle Timing
Single Write
Burst Write
Write
Deselected
CK
tS tH
tKH tKL
tKC
ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated write
ADSC
tS tH
ADV
tS tH ADV must be inactive for ADSP Write
WR2 WR3
A0-An
WR1
tS tH
GW
tS tH
BW
tS tH
BA-BD
tS tH
WR1 WR1
WR2
WR3 WR3
E1 masks ADSP
E1
tS tH Deselected with E2
E2
E2 only sampled with ADSP or ADSC
G
tS tH Write specified byte for 2A and all bytes for 2B, 2C& 2D
D2A D2B D2C D2D D3A
DQA-DQD
Hi-Z
D1A
Rev: 1.11 9/2000
17/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Flow Through Read Cycle Timing
Single Read tKL
Burst Read
CK
tS tH tKH tKC ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated read
ADSC
tS tH Suspend Burst Suspend Burst
ADV
tS tH
A0-An
RD1 tS
RD2
RD3 tH
GW
tS tH
BW BA-BD
tS tH E1 masks ADSP
E1
tS tH E2 only sampled with ADSP or ADSC Deselected with E2
E2
tOE tOHZ
G
tOLZ tKQX Q1A tLZ tHZ tKQ Q2A Q2B Q2c Q2D Q3A tKQX
DQA-DQD
Hi-Z
Rev: 1.11 9/2000
18/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Flow Through Read-Write Cycle Timing
Single Read Single Write
Burst Read
CK
tS tH tKH tKL tKC ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated read
ADSC
tS tH
ADV
tS tH
A0-An
RD1
WR1
RD2
tS
tH
GW
tS tH
BW
tS tH
BA-BD
tS tH
WR1
E1 masks ADSP
E1
tS tH E2 only sampled with ADSP and ADSC
E2
tOE tOHZ
G
tKQ tS Q1A tH Q2A Q2B Q2c Q2D Q2A
DQA-DQD
Hi-Z
D1A
Burst wrap around to it's initial state
Rev: 1.11 9/2000
19/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Pipelined SCD Read-Write Cycle Timing
Single Read tKL Single Write Burst Read
CK
tS tH tKH tKC ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated read
ADSC
tS tH
ADV
tS tH
A0-An
RD1
WR1
RD2
tS tH
GW
tS tH
BW
tS tH
BWA-BWD
tS tH
WR1
E1 masks ADSP
E1
tS tH E2 only sampled with ADSP and ADSC
E2
tOE tOHZ
G
tKQ tS tH Q1A D1A Q2A Q2B Q2c Q2D
DQA-DQD
Hi-Z
Rev: 1.11 9/2000
20/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Pipelined SCD Read Cycle Timing
Single Read Burst Read tKH tKL tKC ADSP is blocked by E inactive
CK
tS tH
ADSP ADSC
tS tH
tS tH ADSC initiated read
Suspend Burst
ADV
tS tH
A0-An
RD1 tS
RD2
RD3 tH
GW
tS tH
BW
BWA-BWD
tS tH E1 masks ADSP
E1
tS tH E2 only sampled with ADSP or ADSC Deselected with E2
E2
tOE
G DQA-DQD
Hi-Z tOLZ Q1A tLZ
tOHZ tKQX Q2A Q2B Q2c Q2D
tKQX Q3A tHZ
tKQ
Rev: 1.11 9/2000
21/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
Sleep Mode Timing Diagram
CK
tS tH tKC tKH tKL
ADSP ADSC
tZZS
~~~~~ ~ ~ ~~ ~
tZZH
tZZR
ZZ
Snooze
Application Tips
Single and Dual Cycle Deselect
SCD devices force the use of "dummy read cycles" (read cycles that are launched normally but that are ended with the output drivers inactive) in a fully synchronous environment. Dummy read cycles waste performance but their use usually assures there will be no bus contention in transitions from reads to writes or between banks of RAMs. DCD SRAMs do not waste bandwidth on dummy cycles and are logically simpler to manage in a multiple bank application (wait states need not be inserted at bank address boundary crossings) but greater care must be exercised to avoid excessive bus contention.
JTAG Port Operation
Overview
The JTAG Port on this RAM operates in a manner consistent with IEEE Standard 1149.1-1990, a serial boundary scan interface standard (commonly referred to as JTAG), but does not implement all of the functions required for 1149.1 compliance. Some functions have been modified or eliminated because they can slow the RAM. Nevertheless, the RAM supports 1149.1-1990 TAP (Test Access Port) Controller architecture, and can be expected to function in a manner that does not conflict with the operation of Standard 1149.1 compliant devices. The JTAG Port interfaces with conventional TTL / CMOS logic level signaling.
Disabling the JTAG Port
It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless clocked. TCK, TDI, and TMS are designed with internal pull-up circuits. To assure normal operation of the RAM with the JTAG Port unused, TCK, TDI, and TMS may be left floating or tied to either VDD or VSS. TDO should be left unconnected.
Rev: 1.11 9/2000
22/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
JTAG Pin Descriptions Pin
TCK TMS
Pin Name
Test Clock Test Mode Select
I/O
In In
Description
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate from the falling edge of TCK. The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP controller state machine. An undriven TMS input will produce the same result as a logic one input level. The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers placed between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP Controller state machine and the instruction that is currently loaded in the TAP Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce the same result as a logic one input level. Output that is active depending on the state of the TAP state machine. Output changes in response to the falling edge of TCK. This is the output side of the serial registers placed between TDI and TDO.
TDI
Test Data In
In
TDO
Test Data Out
Out
Note: This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
JTAG Port Registers
Overview
The various JTAG registers, refered to as TAP Registers, are selected (one at a time) via the sequences of 1s and 0s applied to TMS as TCK is strobed. Each of the TAP Registers are serial shift registers that capture serial input data on the rising edge of TCK and push serial data out on the next falling edge of TCK. When a register is selected it is placed between the TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle or the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single-bit register that can be placed between TDI and TDO. It allows serial test data to be passed through the RAMs JTAG Port to another device in the scan chain with as little delay as possible.
Boundary Scan Register
Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM's input or I/O pins. The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port's TDO pin. The Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. Two TAP instructions can be used to activate the Boundary Scan Register.
Rev: 1.11 9/2000
23/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
JTAG TAP Block Diagram
0
Bypass Register
210
Instruction Register TDI ID Code Register
31 30 29
TDO
*
* **
210
Boundary Scan Register
n
******
***
210
TMS TCK Test Access Port (TAP) Controller
Identification (ID) Register
The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM. It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins.
ID Register Contents
Die Revision Code GSI Technology JEDEC Vendor ID Code 1 10 9 8 7 6 5 4 3 2 1 1 0 0 0 011011001 0 011011001 Presence Register 0 1 1
Not Used
I/O Configuration
Bit #
x36 x18
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 X X X X X X X X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
Tap Controller Instruction Set
Overview
There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific (Private) instructions. Some Public instructions, are mandatory for 1149.1 compliance. Optional Public instructions must be implemented in prescribed ways. Although the TAP controller in this device follows the 1149.1 conventions, it is not 1194.1compliant because some of the mandatory instructions are not fully implemented. The TAP on this device may be used to monitor all input and I/O pads, but cannot be used to load address, data or control signals into the RAM or to preload the I/O buffers.This device will not perform EXTEST, INTEST or the SAMPLE/PRELOAD command. When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01. When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired Rev: 1.11 9/2000 24/33 (c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this device is listed in the following table.
JTAG Tap Controller State Diagram
1
Test Logic Reset
0 1 1 1
0
Run Test Idle
Select DR
0 1
Select IR
0 1
Capture DR
0
Capture IR
0
Shift DR
1 1
0 1
Shift IR
1
0
Exit1 DR
0
Exit1 IR
0
Pause DR
1
0
Pause IR
1
0
Exit2 DR
1
0
Exit2 IR
1
0
Update DR
1 0
Update IR
1 0
Instruction Descriptions
BYPASS When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path. SAMPLE/PRELOAD SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE/PRELOAD instruction is loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and I/O buffers into the Boundary Scan Register. Because the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the TAPs input data capture set-up plus hold time (tTS plus tTH ). The RAMs clock inputs need not be paused for any other TAP operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then places the boundary scan register between the TDI and TDO pins. Because the PRELOAD portion of the command is not implemented in this device, moving the controller to the UpdateDR state with the SAMPLE / PRELOAD instruction loaded in the Instruction Register has the same effect as the Pause-DR command. This functionality is not Standard 1149.1-compliant. Rev: 1.11 9/2000 25/33 (c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
EXTEST EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register, whatever length it may be in the device, is loaded with all logic 0s. EXTEST is not implemented in this device. Therefore, this device is not 1149.1-compliant. Nevertheless, this RAM's TAP does respond to an all zeros instruction, as follows. With the EXTEST (000) instruction loaded in the instruction register the RAM responds just as it does in response to the BYPASS instruction described above. IDCODE The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up and any time the controller is placed in the Test-Logic-Reset state. SAMPLE-Z If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR state. RFU These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction.
JTAG TAP Instruction Set Summary
Instruction
EXTEST IDCODE SAMPLE-Z RFU SAMPLE/ PRELOAD GSI RFU BYPASS
Code
000 001 010 011 100 101 110 111
Description
Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. This RAM does not implement 1149.1 EXTEST function. *Not 1149.1 Compliant * Preloads ID Register and places it between TDI and TDO. Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. Forces all RAM output drivers to High-Z. Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. This RAM does not implement 1149.1 PRELOAD function. *Not 1149.1 Compliant * GSI private instruction. Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. Places Bypass Register between TDI and TDO.
Notes
1 1, 2 1 1 1 1 1 1
Notes: 1. Instruction codes expressed in binary, MSB on left, LSB on right. 2. Default instruction automatically loaded at power-up and in test-logic-reset state.
Rev: 1.11 9/2000
26/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
JTAG Port Recommended Operating Conditions and DC Characteristics Parameter
Test Port Input High Voltage Test Port Input Low Voltage TMS, TCK and TDI Input Leakage Current TMS, TCK and TDI Input Leakage Current TDO Output Leakage Current Test Port Output High Voltage Test Port Output Low Voltage
Symbol Min.
VIHT VILT IINTH IINTL IOLT VOHT VOLT 1.7 -0.3 -300 -1 -1 2.4 --
Max.
VDD +0.3 0.8 1 1 1 -- 0.4
Unit Notes
V V uA uA uA V V 1, 2 1, 2 3 4 5 6, 7 6, 8
Notes: 1. This device features input buffers compatible with both 3.3 V and 2.5 V I/O drivers. 2. Input Under/overshoot voltage must be -2 V > Vi < V DD +2 V with a pulse width not to exceed 20% tTKC. 3. VDD VIN VIL 4. 0 V VIN VIL 5. Output Disable, VOUT = 0 to VDD 6. The TDO output driver is served by the VDD supply. 7. IOH = -4 mA 8. IOL = +4 mA
JTAG Port AC Test Conditions Parameter
Input high level Input low level Input slew rate Input reference level Output reference level Notes: 1. Include scope and jig capacitance.
Conditions
2.3 V 0.2 V 1 V/ns 1.25 V 1.25 V DQ
JTAG Port AC Test Load
50 VT = 1.25 V
* Distributed Test Jig Capacitance
30pF*
Rev: 1.11 9/2000
27/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66
JTAG Port Timing Diagram
tTKH TCK
tTKL
tTKC
tTS TMS TDI TDO tTKQ
tTH
JTAG Port AC Electrical Characteristics
Parameter TCK Cycle Time TCK Low to TDO Valid TCK High Pulse Width TCK Low Pulse Width TDI & TMS Set Up Time TDI & TMS Hold Time Symbol tTKC tTKQ tTKH tTKL tTS tTH Min 20 -- 10 10 5 5 Max -- 10 -- -- -- -- Unit ns ns ns ns ns ns
Rev: 1.11 9/2000
28/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 GS88118/36T TQFP Boundary Scan Register
Order
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 DQB1 DQB2 DQB3 DQB4 DQB5 DQB6 DQB7 DQB8 x36 = DQB9 DQA8 DQA7 DQA6 DQA5 DQA4 DQA3 DQA2 DQA1 ZZ QE DQA5 DQA6 DQA7 DQA8 DQA9 NC = 1 NC = 1 NC = 1 A18
x36
PH = 0 PH = 0 A10 A11 A12 A13 A14 A15 A16 x36 = DQA9
x18
Pin
n/a n/a 44 45 46 47 48 49 50
Order
30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58
x36
A9 A8 ADV ADSP ADSC G BW GW CK PH = 0 PH = 0 A17 BA BB BC BD E2 E1 A7 A6 x36 = DQC9 DQC8 DQC7 DQC6 DQC5 DQC4 DQC3 DQC2 DQC1
x18
Pin
81 82 83 84 85 86 87 88 89 n/a n/a 92 93 94
Order
59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78
x36
FT DP PH = 1 DQD1 DQD2 DQD3 DQD4 DQD5 DQD6 DQD7 DQD8 x36 = DQD9 LBO A5 A4 A3 A2 A1 A0 PH = 0
x18
Pin
14 16 n/a
DQB5 DQB6 DQB7 DQB8 DQB9 NC = 1 NC = 1 NC = 1 NC = 1
18 19 22 23 24 25 28 29 30 31 32 33 34 35 36 37 n/a
NC = 1 NC = 1 NC = 1 NC = 1 NC = 1 DQA1 DQA2 DQA3 DQA4
51 52 53 56 57 58 59 62 63 64 66 68 69 72 73 74 75 78 79 80
NC = 1 NC = 1
95 96 97 98 99 100
NC = 1 NC = 1 NC = 1 NC = 1 NC = 1 DQB1 DQB2 DQB3 DQB4
1 2 3 6 7 8 9 12 13
BPR 1999.08.11
Notes: 1. The Boundary Scan Register contains a number of registers that are not connected to any pin. They default to the value shown at reset. 2. Registers are listed in exit order (i.e. Location 1 is the first out of the TDO pin. 3. NC = No Connect, NA = Not Active, PH = Place Holder (No associated pin)
Rev: 1.11 9/2000
29/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Output Driver Characteristics
120.0
100.0
Pull Down Drivers
80.0
60.0
40.0
20.0
VDDQ I Out
I Out (mA)
0.0
VOut
-20.0
VSS
-40.0
-60.0
-80.0
Pull Up Drivers
-100.0
-120.0
-140.0 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4
V Out (Pull Down) VDDQ - V Out (Pull Up) 3.6V PD HD 3.3V PD HD 3.1V PD HD 3.1V PU HD 3.3V PU HD 3.6V PU HD
BPR 1999.05.18
Rev: 1.11 9/2000
30/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 TQFP Package Drawing
L Symbol
A1 A2 b c D D1 E E1 e L L1 Y
c Pin 1
Description
Standoff Body Thickness Lead Width Lead Thickness Terminal Dimension Package Body Terminal Dimension Package Body Lead Pitch Foot Length Lead Length Coplanarity Lead Angle
Min. Nom. Max
0.05 1.35 0.20 0.09 21.9 19.9 15.9 13.9 -- 0.45 -- -- 0 0.10 1.40 0.30 -- 22.0 20.0 16.0 14.0 0.65 0.60 1.00 -- -- 0.15 1.45 0.40 0.20 22.1 20.1 16.1 14.1 -- 0.75 -- 0.10
L1
D1
e b
D
A1
Y
A2
E1 E
7
Notes: 1. All dimensions are in millimeters (mm). 2. Package width and length do not include mold protrusion.
BPR 1999.05.18
Rev: 1.11 9/2000
31/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Ordering Information for GSI Synchronous Burst RAMs
Org
514K x 18 514K x 18 514K x 18 514K x 18 514K x 18 256K x 36 256K x 36 256K x 36 256K x 36 256K x 36 514K x 18 514K x 18 514K x 18 514K x 18 514K x 18 256K x 36 256K x 36 256K x 36 256K x 36 256K x 36
Part Number1
GS88118T-11 GS88118T-11.5 GS88118T-100 GS88118T-80 GS88118T-66 GS88136T-11 GS88136T-11.5 GS88136T-100 GS88136T-80 GS88136T-66 GS88118T-11I GS88118T-11.5I GS88118T-100I GS88118T-80I GS88118T-66I GS88136T-11I GS88136T-11.5I GS88136T-100I GS88136T-80I GS88136T-66I
Type
ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through ByteSafe Pipeline/Flow Through
Package
TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP
Speed2 (MHz/ns)
100/11 100/11.5 100/12 80/14 66/18 100/11 100/11.5 100/12 80/14 66/18 100/11 100/11.5 100/12 80/14 66/18 100/11 100/11.5 100/12 80/14 66/18
TA3
C C C C C C C C C C I I I I I I I I I I
Status
Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS88118TT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.11 9/2000
32/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS88118/36T-11/11.5/100/80/66 Revision History
DS/DateRev. Code: Old;
New
Types of Changes Format or Content
Page;Revisions;Reason
* Last Page/Fixed "GSGS.." in Ordering Information Note. * Fromatted Pin Outs and Pin Description to new small caps. * Formatted Block diagrams to new small caps. * Formatted Timing Diagrams to new small caps. * Changed "Flow thru" to "Flow Through" in Timing Diagrams. * Boundary Scan Register/Formatted to new small caps. * Package Diagram/Changed "Dimesion" to "Dimension". * 5/Fixed pin description table to match pinouts. * Pin Description/Changed chip enables to match pins. * Pin Description/Changed pin 80 from NC to Address Input. * Pin Description/Rearranged Address Inputs to match order of Pinout * Package Diagram/Changed Dimension D Max from 20.1 to 22.1 * Took out wrong Pinout on page 2 (256K x 32). * First Release of 880 F. * Changed Bump 3C to 4L on first page to correspond SCD pin in BGA pinout. * Changed order of TQFP Address Inputs to match pinout. * Changed order of TQFP DATA Input and Output pins to match pinout. * New GSI Logo. * Changed all speed bin information (headings, references, tables, ordering info..) to reflect 150 - 80Mhz * Corrections to AC Electrical Characteristics Table * Fixed Boundary Scan Register Added Pin 29 * Removed 150 MHz speed bin * Changed 133 MHz and 117 MHz speed bins to 11 ns and 11.5 ns (100 MHz) numbers * Updated format to comply with Technical Publications standards * Updated Capitance table--removed Input row and changed Output row to I/O
Format/Typos GS88118/36TRev1.04h 5/ 1999; 1.05 9/1999I Content
GS88118/36T1.05 9/ 1999I;1.06 11/1999J GS88118/36T1.06 11/ 1999J;1.06 11/1999K GS88118/36T1.06 11/ 1999K88118/36T1.07 1/ 2000L GS88118/36T1.07 1/2000M; GS88118/36T1.08 3/2000N; GS88118/36T1.08 3/2000N; GS88118/36T1.09 3/2000O;
Content content
Content
Content Content
8818 NGS88118/36T1.09 3/ 2000O; 8811836_r1_10
Content/Format
88118_r1_10; 88118_r1_11
Content
Rev: 1.11 9/2000
33/33
(c) 2000, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.

▲Up To Search▲

Price & Availability of GS88118T-115

	To Download GS88118T-115 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .